Question & Answers

1,457 questions in this forum

1. Axial adjusting screw

   Asked by lele.reds, Thursday at 09:44 PM

   0 votes
   0 answers
3. Speed Transmitting Between Motor Gearbox and Gears

   Asked by Engineer88, Sunday at 12:29 PM

   0 votes
   0 answers
4. Thrust Ball bearing and Needle Bearing

   Asked by baris, February 15

   0 votes
   2 answers
5. Hemispherical dome

   Asked by sel ma90, February 10

   0 votes
   4 answers
6. axisymmetric cooling tower

   Asked by sel ma90, February 10

   0 votes
   4 answers
7. What is the best way to approach this problem?

   Asked by levan45, February 13

   0 votes
   0 answers
8. Why is my centrifugal pump shutting down?

   Asked by RyanTW, April 4, 2016

   0 votes
   17 answers
9. 2 radial ball bearings in tandem, is it ok?

   Asked by PabLo Dal Buoni, November 12, 2019

   0 votes
   4 answers
10. new thread on bolt

    Asked by Ronen Burstein, February 6

    0 votes
    0 answers
11. Condensate temperature from steam leaking to atmosphere

    Asked by Derek Frailey, February 3

    0 votes
    0 answers
12. Can one make a chair that can be portable enogh to fit in your pocket?

    Asked by trenton420, January 30

    0 votes
    1 answer
13. what type of motor do I need?

    Asked by alokk, January 31

    0 votes
    1 answer
14. Forces in a Conveyor Belt with Sliding Rollers

    Asked by squeakychair, December 24, 2020

    0 votes
    3 answers
15. Aircraft Architect

    Asked by Mart Mart, November 15, 2020

    0 votes
    2 answers
16. ENGINEERING: Types of Engineers | Engineering Careers (Female Engineers) #2

    Asked by Lois Ndege, December 7, 2020

    0 votes
    1 answer
17. What happens if you physically apply Newton's III 3rd third law of motion, as a cycle system in an engine device?

    Asked by retrodynamic, January 3

    0 votes
    1 answer
18. Simulation Engineering

    Asked by Zor, January 3

    0 votes
    1 answer
19. ViewPorts and Model Space

    Asked by V CHANDRASHEKHAR, January 3

    0 votes
    0 answers
20. Sliding control mode

    Asked by ApertoLibro, December 29, 2020

    0 votes
    0 answers
21. Linear guides for low forces

    Asked by Simas Druzas, December 26, 2020

    0 votes
    0 answers
22. Combustion Chamber Analys

    Asked by bugra, December 25, 2020

    0 votes
    0 answers
23. Gearbox with different speed in clockwise vs counterclockwise

    Asked by Emmett, December 15, 2020

    0 votes
    0 answers
24. Graduated in BS Mech E, did not enjoy any class in special. Not sure what field to pursue/specialization. How did you overcome this challenge?

    Asked by Bob11, December 15, 2020

    0 votes
    0 answers
25. Cbt competency base training

    Asked by Nasir Seinumahama, December 15, 2020

    0 votes
    0 answers
26. CAN YOU HELP ME ABOUT THAT

    Asked by barathe10, November 20, 2020

    0 votes
    1 answer
27. The question is about set screws differences

    Asked by baris, December 8, 2020

    0 votes
    2 answers
28. making a pendulum car as fast as possible

    Asked by S071928, November 25, 2020

    0 votes
    1 answer
29. Biomimetic Jumping Robot

    Asked by Slothaif, December 4, 2020

    0 votes
    1 answer
30. Purpose of different types of bolt/screw heads

    Asked by Vinay.S, October 30, 2020

    0 votes
    8 answers
31. Can vibrations be created due to large pressure differences in air

    Asked by MattG, November 11, 2020

    0 votes
    1 answer
32. Drag Coefficient on Right Angled Isosceles Triangle

    Asked by studentengineer123, November 26, 2020

    0 votes
    1 answer
33. What are the required skills that differentiate Mechanical Engineer?

    Asked by Enoch Mayfield, November 25, 2020

    0 votes
    0 answers
34. Help with quiz

    Asked by arceliaheart, November 17, 2020

    0 votes
    0 answers
35. Shaft boss connection

    Asked by Aurel Elezi, November 8, 2020

    0 votes
    0 answers
36. Looking for a motor design/type that requires no contact with the shaft, high output strength, but servo amount of control

    Asked by vicy vic, November 8, 2020

    0 votes
    0 answers